Compatible Parts List For GTS-T / TYPE M

[Supraclean]

Should delete it :P makes engine bay prettier!

[Pete-R33]

anyone have an idea as to what Clutch Master Cylinder is compatible? the S13 you have to bend or make a new hard line and I dont want to kink it. Is there any? the feed line comes out the bottom, not the side like a s13!

[Supraclean]

Single cam 240sx manual is direct fitment for rb20 gtst transmisson. Confirmed as what's what I'm running on mine. Ordered it at Napa.

[Supraclean]

Sorry read your msg wrong. I used an S14/R33 gts/R34 Clutch master. Just hand to make a custom line tho.

[Sentry]

Hey guys I've got an ECR32 GTS25 (4 LUG!) with a RB25DET swap.

It urgently needs front brakes.

Urgently meaning, what cars do the parts cross reference with so I can pop down to a Napa and have them here in a day?

So far I've found out on my own that Infiniti G20 rotors are what I need, but I've got no leads on pads yet.

What cars can I use pads from?

Remember. 4 lug GTS25-t, not a 5 lug GTST. Single piston caliper.

[Hasley902]

anyone know if there is a compatiable front hub for a 91 gtst mine is cracked

[cschepp]

Ummmmm a r32 hub would work lol. Unfortunately man the hub is not compatible with any other vehicle

[Siscub]

Anyone know if there are compatible rear A-arms?

[beacher1B0]

C & P from your other thread.
Parts master says Z32 non turbo, A31, C33 and R32 GTS? is compatible. No S13 or R32 GTR.
However i believe s13 is the same but thats not what Nissan Parts Master says.

Anyone know if there are compatible rear A-arms?

Nissan Part Master people, Nissan Part Master. This whole section could be deleted if everyone had it. Find the Nissan Fast program 2006, Parts master is included in it. GTRPdoubleUR.com. Sorry Mcfly.

[Voodoo_ChildR32]

Finally found a listing for hicas rear outer tie rod ends(ball joint pressed into knuckle). But the kicker is my cost is $172 each. Soooo I think my supplier has got the wrong listing. I will dig deeper and post up here. If I can source them I'd be willing to order some for guys on here who need em.


Sent from my iPhone using Tapatalk

[Supraclean]

Finally found a listing for hicas rear outer tie rod ends(ball joint pressed into knuckle). But the kicker is my cost is $172 each. Soooo I think my supplier has got the wrong listing. I will dig deeper and post up here. If I can source them I'd be willing to order some for guys on here who need em.


Sent from my iPhone using Tapatalk

I'm pretty sure I paided a pretty penny from Ztune(now monkeynutz) for these aswell so your price might not be that far out.

If I had to do it again, I'd just my a driftworks or Ams lockout kit for the price you would pay for a lockbar/tomei system + Inner/outer tierods.

But anyone is at the same point as you could be a good group buy:P

Sent from my BlackBerry 9700 using Tapatalk

[Voodoo_ChildR32]

Just confirming that a 1990 N/A 300ZX clutch, pressure plate, pilot and release bearings fit an R32 GTST and GTR perfectly. Just installed one for a client of mine and in my own GTR. Also confirming an RB26 flywheel will work as well.


Sent from my iPhone using Tapatalk

[cooke24]

s14 inner and outer tie rods fit and work on ecr33 no problems.

[cooke24]

r33 reverse tranny sensor = z32 reverse tranny sensor

[specialedition]

Hey guys can someone confirm on a clutch slave for an rb20? Is it 240sx ka24de? Please let me know