2.2 Tomei stroker kit Rb20det Rebuild

[1991HCR32]

Hey i just spent about 4-5k all on new parts for my rb20det basically doin a complete rebuild.

How much hp will i acheive with this set up and will i need a tune?

2.2 tomei stroker kit:biggrin::biggrin::biggrin:

brand new oem r34 gtt turbo ( going to run at 13-14psi):biggrin::biggrin:

444cc injectors

upgraded fuel pump

intake

ac completly removed( pump, hoses, rad,)

Fan removed and replaced with electric one



Thanks,

[Skym]

At 13.5psi, should be able to get 320hp at engine with ECU tune (Nistune for stock ECU that modernises stock ECU, so can be reflashed like new car ECU's can), Z32 MAF + Z32 MAF plug / tail.

Be careful with stroker kit, as can make block weaker when it's bored that far and can crack. At least get engine builder to fit sleeves (I noticed can fit thin sleeves to RB block that are hardly noticeable) to add some strength to block. HKS used to fit sleeves with their RB24 (using similar size pistons), etc stroker kits.

[M13]

Be careful with stroker kit, as can make block weaker when it's bored that far and can crack. At least get engine builder to fit sleeves (I noticed can fit thin sleeves to RB block that are hardly noticeable) to add some strength to block. HKS used to fit sleeves with their RB24 (using similar size pistons), etc stroker kits.

I'm gonna go out on a limb and say the stroker kit does not touch the bore but rather the stroke





Where did you source this stroker kit from?

[Skym]

2.2 litre = Tomei Pistons, stock conrods.

2.4 litre = Tomei Pistons, GTR conrods, GTR crank (have to knotch bottom of cylinders, so conrods clear).

Stock bore is 78mm, Tomei Piston is roughly 82mm + additional room for expansion of piston when hot, etc.

There is stock pistons from another engine (4AGZE?? pistons) that can be used for RB24 conversion.

[1991HCR32]

So it would roughly put 300hp to the wheels. And my ecu is stock so what exactly is nistune? is it a dyno company or.? Im located in alberta i belive there is only a few dynos around here.

[Skym]

320hp at engine is roughly 190rwkw or 255rwhp. Also need FMIC, BOV if you don't have them. With intake, exhaust from dumppipe, FMIC, BOV, should produce 13.5psi without boost controller.

With dumppipe, boostcontroller, 1bar / 14.5psi, 330hp+ at engine is possible.

Nistune is a product that converts stock ECU, so it can be retuned via Consult diagnostic plug (under drivers side of dash), Consult diagnostic cable, laptop with tuning software.

More info about Nistune -

http://forums.gtrcanada.com/group-bu...buy-50623.html

[C-unit]

am I missing something?

4-5k later you are running semi forged internals that is 2.4L and pushing a GTT turbo?

Why not just get a rb25..............

[1991HCR32]

am I missing something?

4-5k later you are running semi forged internals that is 2.4L and pushing a GTT turbo?

Why not just get a rb25..............


That was the cost for my rebuild. If i put in a rb25 it would still be old and such and such. i had an rb20 to work with so i basically restored it with some mods. the plan is to not pull out the wrenches for a long time. also what is fmic

thanks skym you are a great help!

[kyles_r32]

fmic = Front Mount Inter Cooler

[RSi]

I'm gonna go out on a limb and say the stroker kit does not touch the bore but rather the stroke





Where did you source this stroker kit from?

HAHAHA I think you are pretty safe on that limb