Tweet
I have decided to go a new route with my gtr and such I will be parting out the engine and some interior bits.
Will update as I go, winter is not fun.
I dont care if you have a friend who has one cheaper etc etc. The prices are based off of wear, and market listings. I doubt Ill find many buyers here but cant hurt. Also listed on ebay etc.
EXEDY CARBON-D TWIN SKYLINE GT-R BNR32 RB26DETT Push type
$2300
The disks show minimal wear of 5.46mm from 5.5mm max wear is 4.7mm.
Metal facing surfaces show wear and heat marks that are normal for carbon type clutches.
Very strong legs needed for actuation, its like pushing a wall to engage.
You can get the wear parts from exedy still, as in disks and other pieces.
All parts included
CM31S Clutch Cover
FM36 Fly wheel
8x Clutch cover allen bolts
6x Fly wheel bolts
6L23A DD01 Damper puck
1x Metal top wear surface
1x Metal middle wear surface
2x Carbon disk
Part Number: NM032HDMC1
Clutch Type: Carbon-D Twin
Friction Facing: Carbon
Disc Diameter (mm): 225
Sprung Centre: Yes
Clamp Load (N): 13500
Torque at Flywheel: 550 lb-ft / 740 Nm
Torque at Wheels: 440 lb-ft / 600 Nm
Parts are used and as such there will be no refunds
This is a push type clutch so zenki bnr32 fitting
Any questions please ask
Kijiji link http://www.kijiji.ca/v-transmission-...ationFlag=true
The next parts will be:
Laminova radiator/oil cooler, ss lines, nismo r33 n1 oil block
Alcon 4 piston brakes with ferodo ds250011 pads, 355mm floating 28mm thick disk, ss hardlines, fits 240sx's if they have a 300zx hub
9 point bolt in through dash roll cage
HKS EVC 4 Boost controller with high psi solenoid
HKS GT2540s
24u block (spun rod)
jun cams intake 264 9.1mm lift exhaust 272 9.1mm lift
trust 2.7l stroker kit (spun rod, depending on repair I would get the surfaces redone and repaired)
550cc injectors, billet fuel rail, braided lines
Head machined for high lift cam
and more. Photos and pricing will be up when I get them done, send a message if you want to know specifics will not entertain lowball offers, I know the price and the market.
Will update as I go, winter is not fun.
I dont care if you have a friend who has one cheaper etc etc. The prices are based off of wear, and market listings. I doubt Ill find many buyers here but cant hurt. Also listed on ebay etc.
EXEDY CARBON-D TWIN SKYLINE GT-R BNR32 RB26DETT Push type
$2300
The disks show minimal wear of 5.46mm from 5.5mm max wear is 4.7mm.
Metal facing surfaces show wear and heat marks that are normal for carbon type clutches.
Very strong legs needed for actuation, its like pushing a wall to engage.
You can get the wear parts from exedy still, as in disks and other pieces.
All parts included
CM31S Clutch Cover
FM36 Fly wheel
8x Clutch cover allen bolts
6x Fly wheel bolts
6L23A DD01 Damper puck
1x Metal top wear surface
1x Metal middle wear surface
2x Carbon disk
Part Number: NM032HDMC1
Clutch Type: Carbon-D Twin
Friction Facing: Carbon
Disc Diameter (mm): 225
Sprung Centre: Yes
Clamp Load (N): 13500
Torque at Flywheel: 550 lb-ft / 740 Nm
Torque at Wheels: 440 lb-ft / 600 Nm
Parts are used and as such there will be no refunds
This is a push type clutch so zenki bnr32 fitting
Any questions please ask
Kijiji link http://www.kijiji.ca/v-transmission-...ationFlag=true
The next parts will be:
Laminova radiator/oil cooler, ss lines, nismo r33 n1 oil block
Alcon 4 piston brakes with ferodo ds250011 pads, 355mm floating 28mm thick disk, ss hardlines, fits 240sx's if they have a 300zx hub
9 point bolt in through dash roll cage
HKS EVC 4 Boost controller with high psi solenoid
HKS GT2540s
24u block (spun rod)
jun cams intake 264 9.1mm lift exhaust 272 9.1mm lift
trust 2.7l stroker kit (spun rod, depending on repair I would get the surfaces redone and repaired)
550cc injectors, billet fuel rail, braided lines
Head machined for high lift cam
and more. Photos and pricing will be up when I get them done, send a message if you want to know specifics will not entertain lowball offers, I know the price and the market.
Comment