FS: RB20/25/26 parts, R32 & S13 parts

[ARC240]

Hey guys, gotta clean out the garage because it's starting to turn into a mess again and these parts are just collecting dust. If you don't see a price or it says OBO, send me your offer, no reasonable ones will be turned away. Shipping is not included in the price unless noted. Buyer pays shipping & PayPal fee.

Here we go...

DENSO/SARD 700cc or 720cc injectors: I have a set of 6 used Denso/SARD 700 or 720cc, not sure exactly (number on the injector says: 195500-0830), came out of a running RB26, I was contemplating keeping them for use on my build, but I'm in need of the money for other things on the car right now, so if I get the right offer, I may let them go. Will also work on RB20 and 25 (top-feed fuel rail only), as I also have the GTR injector resistor for it. - BEST OFFER

RB20DET Parts:
-Clutch & Flywheel Combo: still in decent shape. - $65 OBO






-RB20DET Crankshaft: in good shape, has been sitting out of a long block for over a year now so the bearing surfaces are a little tarnished and like any crank prior to reinstalling, should be polished at a machine shop. Still has crank bolt and old oil pump on it. - $90 OBO

-RB20DET stock cams: good shape, like the crank, need a polishing before they're tossed back into a car. - $30



-RB20DET Turbocharger Intake Flex Hose: 2 avilable, both in great shape, this is the one that goes between the MAF and turbo. - BEST OFFER


-RB20DET t-stat housing/water neck: good condition! - $10 OBO


-RB20DET OEM cam gears: have 2 sets, no bolts/lock plates included - $20/pair OBO


-RB20DET OEM intake manifold: bare intake manifold with water pipe, no sensors, tb or injectors, good for a project manifold. - BEST OFFER


-RB20DET recirc/breather pipes - $10


-BLITZ ACCESS ECU for RB20DET: Not sure what it's tuned for, tested, manages an engine just fine. NOTE: has previously been opened to make sure it was genuine and it IS genuine, chip is soldered right into the board. - $225 OBO


-Starter for RB20/RB26: came off of a running RB26 - $50


RB25DET
-R33 RB25DET engine brackets & rubber mounts: good shape, cannot be used for RB25 into R32, these are stock R33 GTS-t engine mounts. - BEST OFFER

-RB25 Turbo Actuator - BEST OFFER


RB26DETT
-Starter for RB20/RB26: came off of a running RB26 - $50


R32:
E-brake handle assembly - boot's in rough shape, still fully functional - BEST OFFER

S13:
Flip-up sealed beams - in good working order, switched them out only because I converted to H4 housings. - BEST OFFER

Head unit/shifter trim - good shape, need gone - $10

Real "wet" carbon fiber wrapped ashtray for S13 - $40

[GTS-James]

What's the process of installing the ecu?

[ARC240]

It's not hard at all, you need to remove the passenger side (left side on a Skyline) kick panel near you left foot, undo 2 10mm bolts, and one more top bolt holding the harness connector to the ECU, pop the harness connector out, put the Blitz on the ECU connector and tighten the 10mm connector bolt. Should take around 10 mins total.

[coldshot888]

if u still have the injectors i really could use those,, i nevr use this forum so plz email me, coldshot888@hotmail.com

[R32_GTR]

i assume you have a forward facing plenum now, was wondering what you did if anything to the t-stat housing for clearance on the plenum?

[ARC240]

i assume you have a forward facing plenum now, was wondering what you did if anything to the t-stat housing for clearance on the plenum?

??? what, i wish i had a front facing plenum , these are spare parts from another 20 that i parted.

BUMPPPPPPP!!!