Tweet
Plans changed, no longer need this.
Was in perfect working order with 145-150 compression across the board. Below are prices that are OBO but what i feel to be fair, more stuff bought = better deal so dont be afraid to shoot an offer. Everything will be PLUS shipping.
Bare 05U Block, hot tanked,magnafluxed and quick hone painted black,comes with cradle and squirters - $350
OEM R32 crank, should get a collar but clean otherwise,no scoring- SOLD
Polished Valve covers 8/10 condition could use a quick reshine - SOLD
cam covers, coil cover and front timing cover)
Complete RB26 engine harness, uncut - $250
1 complete set of 6 OEM pistons and rods complete with rings, very minimal det on 2 piston tops , have been wire wheeled and cleaned(had good compression but rings should be replaced anyways so im not saying to use them) - $100
1 set of OEM Pistons, and wrist pins - $50
2 Stock GTR Turbos, minimal shaft play, no smoke, semi polished housings and polished wg actuators - $250, can include stock manifolds,elbows aswell
RB26 Y-Pipe for turbos- $60
2 GTR Mafs - Pending
3 Cam angle sensors - $70 each (tested working condition)
Rb20/26 ignitor- Pending
Greddy clear timing cover, says RB26 on it, one small crack at bottom- $70
OEM Valve seals intake and exhaust - $40
OEM valves, springs, retainers - $100
OEM camshafts - $50 a set, have 2 sets
OEM water pump - $30
Intake plenum assembly, with ITB's and AAC valve - SOLD
Fuel rail - $40
Injector resistor box - $50
GTR rear 6 bolt axles- sold
R200 diff, stubs - $180
GTR 5 lug hubs, 1 needs bearing - $50
OMP Universal seat rails, side mount - $50 never used
Blitz intake filters and adaptors - $140
BNIB supertech intake and exhaust valve guides RB26- $SOLD
Coilpack harness - Pending
R32 GTST rims, clean no rash repainted gun metal grey with center caps 9/10 condition no tires - $180
GTR front drive shaft - $50
GTR rear drivshaft - $80
Stock RB20 ECU - $90
RB20 polished valve covers and custom vented coilpack cover powdercoated black - $100
RB25 intake OEM intake plenum - $80
RB20 intake plenum OEM- $80
RB26 knock sensors - $50 for the pair
If you need anything not listed PM me and i may have it. Parts located in BC Canada, will ship! Can also use paypal now aswell!
Was in perfect working order with 145-150 compression across the board. Below are prices that are OBO but what i feel to be fair, more stuff bought = better deal so dont be afraid to shoot an offer. Everything will be PLUS shipping.
Bare 05U Block, hot tanked,magnafluxed and quick hone painted black,comes with cradle and squirters - $350
OEM R32 crank, should get a collar but clean otherwise,no scoring- SOLD
Polished Valve covers 8/10 condition could use a quick reshine - SOLD
cam covers, coil cover and front timing cover)
Complete RB26 engine harness, uncut - $250
1 complete set of 6 OEM pistons and rods complete with rings, very minimal det on 2 piston tops , have been wire wheeled and cleaned(had good compression but rings should be replaced anyways so im not saying to use them) - $100
1 set of OEM Pistons, and wrist pins - $50
2 Stock GTR Turbos, minimal shaft play, no smoke, semi polished housings and polished wg actuators - $250, can include stock manifolds,elbows aswell
RB26 Y-Pipe for turbos- $60
2 GTR Mafs - Pending
3 Cam angle sensors - $70 each (tested working condition)
Rb20/26 ignitor- Pending
Greddy clear timing cover, says RB26 on it, one small crack at bottom- $70
OEM Valve seals intake and exhaust - $40
OEM valves, springs, retainers - $100
OEM camshafts - $50 a set, have 2 sets
OEM water pump - $30
Intake plenum assembly, with ITB's and AAC valve - SOLD
Fuel rail - $40
Injector resistor box - $50
GTR rear 6 bolt axles- sold
R200 diff, stubs - $180
GTR 5 lug hubs, 1 needs bearing - $50
OMP Universal seat rails, side mount - $50 never used
Blitz intake filters and adaptors - $140
BNIB supertech intake and exhaust valve guides RB26- $SOLD
Coilpack harness - Pending
R32 GTST rims, clean no rash repainted gun metal grey with center caps 9/10 condition no tires - $180
GTR front drive shaft - $50
GTR rear drivshaft - $80
Stock RB20 ECU - $90
RB20 polished valve covers and custom vented coilpack cover powdercoated black - $100
RB25 intake OEM intake plenum - $80
RB20 intake plenum OEM- $80
RB26 knock sensors - $50 for the pair
If you need anything not listed PM me and i may have it. Parts located in BC Canada, will ship! Can also use paypal now aswell!
Comment