Reflections-Detailing Portfolio

[Reflections]

The car was a good customers personal daily driver. Not having it parked in a garage, and lots of trees meant it was dirty and contaminated. Also, most likely brush washes and improper wash techniques were used. Paint was corrected about 75%.

Wash
CG CWC+ Zep Citrus Presoak (4:1)
MF Chenile for paintwork
Grout Sponge for lower half
Diamondite Bug Remover Presoak
Bug Sponge
RG for badges and seams
Peanut Butter (for the wax on rubber- worked wonders)

Wheels
RG Wheel Brush
RG (SV Style) Brush
Brown Royal 2:1
MF Mitt (wheel face)
EZ Detail Mini (behind spokes)

Clay
ONR Lube
Ricardo Yellow

Polish
PCXP
LC 5.5" +4" Orange
Menzerna SIP (left the finish great on the hard paint, but also removed a good amount of defects)

Sealant
Menzerna Power Lock

Interior
ZEP High Traffic Carpet Cleaner
Brush
PB Natural Look
Meguiars M40
APC 10:1
Croftgate Leather Protectant/Conditioner

Befores:

















During:

Foamed with Brown Royal 2:1


After a few short passes! Yikes...


Polish needed some QD to being removed fully


Much better! No more damage (almost)


Good clarity in the trunk!


Much better than that mess on the hood before!


Hmm... That seems quite heavy.


Gone!

Afters:













Interior:






Thanks for Looking! If you have any questions feel free to ask and I can help you out!

[mfroese]

Good results and welcome to the forums. May want to read http://forums.gtrcanada.com/media/45...edia-only.html which is stickied to the Media section. Off Topic anything goes, feel free to post more in that section. If you detail anything Skyline related post it up!

[Reflections]

Good results and welcome to the forums. May want to read http://forums.gtrcanada.com/media/45...edia-only.html which is stickied to the Media section. Off Topic anything goes, feel free to post more in that section. If you detail anything Skyline related post it up!

Ahh yes. I did read that but using Cobraas outline, I placed it where he had his work.

[DarkCaporaL]

I don't think it matters much....just detail one Skyline and then you'll be good.

Nice work.

[Reflections]

I don't think it matters much....just detail one Skyline and then you'll be good.

Nice work.

Never had one before, any takers Lol. I would kill for a ride in one. Hopefully the guy in my neighborhood is a member here.

[Reflections]

This car belonged to the wife of my previous customer. He wanted the same type of service offered. The car was hammered! After test spots with M105 being hit a few times, the rids were just too deep to be safe. The rear bumper also had way too many dings, and rough exposed areas that my pad would tear over them. Deep scuff on the passenger side that is a large line and through the paint into exposed metal worries me about rust.

So background info on the paint hardness- this thing is rock hard! M105 finished LSP ready with an orange pad (best balance of defect removal vs. gloss in this case).

Wash
2BM
CG CWC+Zep Citrus Presoak on lower panels
RG Detail Brush on vents and badges
Bug Sponge on front bumper

Wheels
Tires- ZEP Citrus 2:1
Wheels- ZEP Citrus 4:1
Dressed with Opti-Bond 1:1 with a Purdy Brush (next best thing to a Pneu Brush)

Clay
Ricardo Yellow
ONR Clay Lube

Polishing
PCXP
LC Flat 5.5", 4" Orange
M105

Exhaust
Scotch Brite with OPT to remove the caked on residue and it created a clean stainless-steel look
Optimum Metal Polish on Dremel with felt tips (restored the gloss to factory)

LSP
Glaze- PB Black Hole
Sealant- Menzerna Power Lock

Befores:

Through the paint Nothing I could do on the edge


The "other" guys pro detailing...


A side view of what's in store for the next morning


German brake dust! Don't breath this


Let's see what we can do


This thing has a lot of carbon buildup


Really should take more interior befores... It was like this in all four corners+coffee stains

During:

Top cleaned with APC 10:1


After a wash...Whats really lurking under!


The obligatory 50/50 shot :


Afters:


Dripping wet!


Swirls B Gone!




Tight beads


Mats are drying


Zebra under the carpet? Overkill?


Still some defects left... err!


Stretching topless




Not bad, not bad at all!



Near 9h

Thank for looking folks!

[cobrAA]

Ahh yes. I did read that but using Cobraas outline, I placed it where he had his work.

I don't know if I should be flattered or either insulted. I will stay at this. Keep it up.

[DarkCaporaL]

One of you is in the GTA while the other is in Montreal, it's all good.

[Reflections]

I don't know if I should be flattered or either insulted. I will stay at this. Keep it up.

Hardly! You do great work, and I just didn't know where to post- so I used the Media section as you did. You do some fantastic work yourself, please don't take this as an insult AT ALL.

[Reflections]

Long story short me and Hamza got a chance to detail this badboy. Swirls weren't terrible but there were many rids and deeper scratches the owner wanted taken care of. Paint was on the low side reading around 100-120, and it was odd to see so little metal panels on the car in general. 2 Meguiars microfiber foam pads later and 9h, it was completed... and then the rain came along. The front of the hood was wet sanded to remove deep scratches and marks.

Products Used:
CG Citrus Wash and Clear
Brown Royal Wheel Cleaner 2:1
ONR Clay Lube
Ricardo Clay
IronX
OPT Opti-Bond
CG Barebones
OPT Metal Polish
P21S Polishing soap
M105+M205
Permanon Platimum
Blackfire Wet Diamond

Before shots:



That german brake dust...

Could definitely look better!



Swirls on swirls

And again...

The plan of attack for the wheels. Going to battle it out.

During Shots:

When do you foam? "When I get bitten by a stray dog."

DIY foam gun does the job alright, its dwelling!

Sun made its visit a few times... German rivalry across the street.

Nasty wheels, and MB really chose some horrible lug nuts they look 30years old already!!

Looks clean enough to you right?

Wrong! IronX doing it thing on the barrels.

SHINY!!! No dressing yet though.

Real thick mitt! Super soft too, easily gets into all the crevices compared to a sponge.

Exhaust before...

After. It was actually very shiny, but it was warm from the drive.

Oddly enough this side was cool, and looked a ton better during photos.

Post-Wash.

Its just the photos... paint was far from perfect.





Trying to get get it bleeding... black is very impossible to see IronX working

Photo creds to Hamza.

[Reflections]

Getting that polisher going! Fantastic correction but M105 on its own left some hazing.

Before... What. A. Mess.

After... cleared up perfect!

Alas, looking like it arrived from the showroom.

Perfecto!








Finishing touches on the beast.

After Shots...

Getting late... short on time. Sun shots another time





Paint was glowing!

Thanks for looking!

[cooke24]

M105 and M205 are the best products out there hands down.

My manager disagrees about m105 and m205, takes too much effort and time. It pisses me off sometimes as we just make customers cars look shiny and basically use products that fill in scratches, thus not removing them and in about 2 months the swirls and scratches are back. He wants the polishing done in about 20 mins, i tell him if you want it done right ill see you at the end of the day.

anyways sick work man, hard to find people that know there ****.


btw what polishing and cutting pads are you using?