Friday April 10 Mission Drag Racing ! Whos in...

[Chris_RB]

160 is not that much... you should trap close to 120mph (192kph).

My Gts-t with a cat-back, FMIC and boost controller at 12PSI ran a 14.1 at 98MPH (160kph ish).


if you're getting wheel hop, you need new diff bushings.

for now, just slip the clutch a bit more... and lower your launch to about 3500-4000RPM

slipping a twin plate takes some precision...lol, Will try. I'm not sure it was that long (the 400m).

Diff bushings eh? have to look into that. I thought it should be pretty tight with that diff and suspension (no hop).

[SkunkWorks]

I could come as the media entourage...

[Nitrouz]

slipping a twin plate takes some precision...lol, Will try. I'm not sure it was that long (the 400m).

Diff bushings eh? have to look into that. I thought it should be pretty tight with that diff and suspension (no hop).

slipping a twin plate is indeed not a walk in the park. What I do is right at the friction point, hammer the throttle and then let go of the clutch completely a split second after. Just so it rolls forward ever so slightly right before you let go of the clutch. After a few tries, you'll get used to the timing.

Sounds pretty dumb I know, but it worked when I was using a twin plate carbon clutch.

[Chris_RB]

slipping a twin plate is indeed not a walk in the park. What I do is right at the friction point, hammer the throttle and then let go of the clutch completely a split second after. Just so it rolls forward ever so slightly right before you let go of the clutch. After a few tries, you'll get used to the timing.

Sounds pretty dumb I know, but it worked when I was using a twin plate carbon clutch.

Sometimes I do that at traffic lights but I would probably hold the clutch a split second longer for a bit more pull off the line. But sometimes I swear it grabs differently at times. After a few pulls I'm sure I will be more successful Should be fun

[Nitrouz]

Sometimes I do that at traffic lights but I would probably hold the clutch a split second longer for a bit more pull off the line. But sometimes I swear it grabs differently at times. After a few pulls I'm sure I will be more successful Should be fun

yeah usually carbon clutches' friction points change quite a bit due to temperature. Ride it for a couple of seconds first before you launch. Then it would be a little more consistent.

Good luck.

[Gaelen]

straight from missionraceway.com

ATTENTION: Due to ongoing construction at MRP all drag racing events scheduled for April 10, 11, 12 have been CANCELED. Further information will be forthcoming.

All those who were accepted into the Friday April 10 test & tune will be carried over to be in the Friday April 24 test & Tune. If you cannot make this date please phone the office to let them know.

[Zulu]

Lame - I guess we all need to revert to my other post about a nice cruise.

See the April 10 post in Western and come for a nice drive.

[Chris_RB]

aw crap!

[Nitrouz]

I've changed the meet date on niclub to April 24th instead.

[BlackR32]

Damn that sucks! First day of the year I guess we have next week

[dah_hunter]

This only means Friday can be epic is some other way..

:-)

[JBNR32]

Crap, I was hoping to make it out.

[DeviantRebel442]

YES YES YES!!!!!! THANK YOU SO MUCH....

i can make it out on the 24th...gues whos dragging now...time to see what a shitty driver and a stock GTR can do...

[mvs2]

I'll be there..just watching though :P

[RyanGTS-T]

will I break into the 20's?

I will race you in the Rolla.

I think it would be fun.

This is if my car makes it to mission. It was just assaulted in a road rage incident. ******* maple ridge people, such a getto.