Skyline R32 GTS-4 rear outter tie rod?

[BigJamal88]

hey, i have been searching this for awhile, and i had no luck. well im looking for rear gts4 outter tie rods? anyone know what USDM nissan part would fit this? any where i can source these for a good price?

[Bravo]

I'm thinking it was the 300zx 2+2!?

[BigJamal88]

can anyone confrim what fits forsure? im pretty sure its the same as the rwd skyline?

[Voodoo_ChildR32]

I think I tried those already and they are not even close to the Skyline rod ends.


Sent from my iPhone using Tapatalk

[BigJamal88]

im pretty sure the rwd tie rods will fit? if they do, i have access to one, i should pick it up and maybe compare them to others? i really gotta get this fixed.

[beacher1B0]

If your lookin for just the Rear Tie Rod Ball joint assembly, Parts Master says Z32 VG30DTT, R32 RB20det 2wd and 4wd, R32 GTR are all the same Part #.

Go to Nissan and be done with it. Ball Joint Assembly - Rear Axle - 55154-30P00.

[BigJamal88]

I also need the Outter tierod end with the ball joint. So does anyone know what exactly fits on the gts4 before i go insane.

[Daryl @ RightDrive]

The GTS4 ones will fit perfect! I might have some at the shop, will have to check next week when back in the office.

[beacher1B0]

I also need the Outter tierod end with the ball joint. So does anyone know what exactly fits on the gts4 before i go insane.

Front or rear?

[BigJamal88]

Rear outter tie rod

[cschepp]

300zx twin turbo. Not the na version. These should fit as the Gtr parts are the same as well.

[TorqueSplit]

Hi Everyone,
Please - no one kill me for reviving an older post as I'm merely trying to be helpful... I wanted to offer the Nissan Part Numbers that I have looked up on "FAST" for Tie Rods (Front and Rear) for R32's... Of course the "Rears" only apply to HNR and BNR models... I own an HNR32 with a RB26 Swap in it so I know all the advise people tend to give who think they know about Skylines but don't own one, or peeps that only know about GTS-t's... Then there is the majority of folks who have a good bit of actual knowledge and make me want to help... So I do understand that the small group of us HNR drivers are the somewhat "hybrid" of the GTS-t and GT-R platforms... So before anyone trolls me - I know what I'm talking about.

(Front)
SOCKET KIT-TIE ROD, OUTER -- 48520-33P25 (alt 48520-33P26) Also appears to be a 300ZX part number on nissanpartszone.com $76.39

SOCKET ASSY-TIE ROD, "INNER" -- 48521-10V06 (alt 48521-10V08) Also appears to be a 300ZX part number on nissanpartszone.com $134.09

(Rear)
LINK-LOWER, REAR SUSPENSION, OUTER -- 55114-39F10 (Driver Side) Also a 240SX part number on nissanpartszone.com (I didn't know they made HICAS 240's? Or do they use these on the front?) $47.61

LINK-LOWER, REAR SUSPENSION, OUTER -- 55114-39F00 (Passenger Side) Also a 300ZX and 240SX part number on nissanpartszone.com (again on the 240's?) $47.61

SOCKET ASSY, "INNER" -- 48521-35A06 Also appears to be a 300ZX, 240SX and Sentra part number on nissanpartszone.com (...and the Sentra's too?) $61.42


Notice the "INNER's" really aren't called "Tie Rods" but rather "SOCKEY ASSY's"... I think the Tie Rod boots are part of the whole OUTER Tie Rods too - so I've not seen any info on separate boots being available in case anyone was looking. I've looked at a couple of prices on other sites and I thought I found a few for as low as $35.00, but I don't recall if that was OEM or not. You may want to also check your ball joint boots for rips before starting this job...

As always, I hope this post is helpful to peeps out there... If anyone needs a screen shot from Fast, just shoot me a PM.

Ken