BNR320001551 Build

[R32GT-R]

http://www.youtube.com/watch?v=ta_MHAhSjlM

I had an older build thread going but i left my Internet provider and i lost most of the pictures. So i am on to stage two, motor build. to look at the older thead, with no pics. http://forums.gtrcanada.com/showthread.php?t=20366

Tuning:

Apexi PFC
Motec PLM
FC Datalogit V2


Spec List:

BNR32-001551

ATL 22 gallon Fuel Cell with two surge tanks
Bosch 044 pumps * 2
Canton 1 micron filters
Earls Check Valves
-8an * 2 Feed lines
-8an Return
Sard 800cc green top injectors
Sard fuel rail
Sard Type RJ Regulator
Battery mounted in trunk - Custom box
Re and Re rear sub frame powder coat black
NEW wheel bearings rear
Re and Re CV boot kits rear
Nismo Long Studs F&R
Energy Poly Bushings
Removed Hicas,A/C, Park Brake
Defi BF Guages, Tac,Pyro,Boost,Oil Press,Water,Oil Temp
Apexi PFC,Controler, Boost Kit
Z32 AFM's new
Trust 600*300*115 IC
Trust T618z
Trust Front Pipe 2 pc
Custom recirc BOV kit
Trust Raidiator
Trust Coolent expansion tank
Trust Oil Catch
Trust Hard Pipe kit
Trust Oil Cooler Relocate thermo
OS Giken Superloc Rear
Cusco Tension Rods Front
Cusco Front Upper Camber -5mm
Cusco Front Sway Bar
Cusco Rear Sway Bar
Cusco Rear Upper link
Cusco Rear Toe Bar
Cusco Rear Strut Bar
Nismo Front Strut Bar and Master cyl stopper
JIC Magic FLT-A2 Coilover 10 kg F 8kg R
Custom Ti Exaust 90mm
Custom Test Pipe with WideBand
Motec PLM
F50 Big Brake Kit Front
Nismo LM 17" Wheels
Nismo Engine mounts
Nismo Transmission mounts
Tomei 280 deg 10.25mm ProCams
Tomei Oil Pan
Tomei Oil Pump
Tomei Bronze valve guides
Tomei Lifters
Tomei Spec C Spring kit +10,000 rpm
Tomei Valve seats
N1 Water Pump
Cusco Cooling Plate

Body and Paint:

Full glass out restoration, Re & Re of any problem areas. Paint with two tone HOK Kandy BrandyWine with a Black roof and A&C Pillars

[R32GT-R]

Ztune has started my RB26 head build.

Tomei 280 deg 10.8 lift cams
Tomei lifters,guides,seats
Tomei Spec C springs
Tomei Cam Studs
Oil Drainback
Portpolish
Bowlwork













Short block will be 2.6l.

Parts in my garage, build starts this winter.

Tomei Oil Pump
Tomei Oil Pan Service (Pan Extention)
Mahle Powerpak 87mm pistons
Tomei 2.6l Full Counter Balance Crank Shaft
N1 Water Pump











Tomei Full Counter CrankShaft



Mahle PowerPak Pistons "slipper skirt"

[NismoS-tune]

Is your VIN right? It looks to have an extra digit, unless mine as a missing one lol. I must be crazy. 11 digits is right no?

[R32GT-R]

ya i think you are right

[NismoS-tune]

oh btw, there's nothing better than good head Sweet looking setup!

[R32GT-R]

With choosing rods i dont know if i should go with heaver stronger Carrillo H beam or Lighter Super-A beam

488 vs 507 grams

[R32GT-R]

added a video at the top

[Rapier46]

hahaha sounds ******* epic

[R32GT-R]

Tomei Oil Pump





Tomei Oil Pan

[Chewy]

mmmm sexpan.

[R32GT-R]

Any one know how to properly store a crankshaft till i am readdy to use it?

I just sprayed with move-it penetrating oil and stood on end by bolting to stock flywheel. wrapped in a plastic bag.

[derk]

place it on end, or in V-blocks supporting the mains

[NismoS-tune]

The tomei pump and pan are a good choice. Not a bad way to speed $3000 lol. Could you PM me where you got them from? Thanks.

[R32GT-R]

just bought a Exedy Hyper Twin
to replace my HKS GD Pro

[Rapier46]

heyyy did you get that clutch from nathan? if so, i have personally humped that clutch.