Compatible Parts List For GTS-T / TYPE M

[ARC240]

Yep. Nismoparts sent me an RB25 clutch slave and it didnt fit then i looked over at my tranny from my KA24E and the slave looked like itd fit and sure enough
lined right up!

good stuff, posted edited. Wasn't sure if the one from the KA-E would fit, so I just listed what I used and worked for me.

[kkeith]

Hey guys, i found it a little hard to find what i needed going through all these pages so i copied and pasted everything into a single file, I figured i'd post it on here to help everyone else out as well.


Oil Filter - 240sx or 300zx
Fuel Filter - 300zx (have to remove the stock holder bracket in order to make it fit)
02 Sensor - 1990-94 300zx TT driver's side (left side)
Brake Pads - 300zx TT both front and rear.
Rotors - 300zx z32 tt front and rear.
Clutch - rb25 and VG30DE 300zx non turbo
Thermostat - VG30DE(TT)
Brake master cylinder - 91 Pathfinder
Rear shocks - S13(240sx) and GTR
Front tension rods - 300ZX(Z32) and S13
Almost all of the other suspension bars are the same as 300ZX including the energy suspension master bushing kit
Tie rod ends - maxima A32
Inner and outer (Front&Rear)CV boots - Z32 non-turbo
Trany front cover oil seal - D22 '00 K24DE
Shifter bushings - S13
Diff side oil seal - '90-'93 300zx Z32 non-turbo
Diff side bearing - Pathfinder WD21 '90-'93
Drive pinion oil seal - Pathfinder WD21 '88-'90
Drive pinion bearing - (F&R) Z32 non turbo
Inner rear CV joint - Z32
Front wheel bearing - Z32
Temp/Oil/Boost sensor - '90 Z32
Mag. starter solenoid switch - B14 91 GA16DE MT only
Power folding mirrors - S13
Heater core - U12
Blower fan and motor - P10
Rear inner Tie Rods - z32 300ZX TT
Lug Nuts - 300zx z32
Front inner tie rods - 90-96 infinity g20
Oil Sending Unit (pressure switch) - '91 300zx tt
Front Outer Tie Rods - 1995 Nissan Maxima
Alternator - 1989 - 1990 Nissan 240sx alternator off a KA24E or A32 Maxima
lower control arm - infinity q45
Ignitor - z32 http://forums.nicoclub.com/zerothread/251366

[Rblove26]

I've got a 94 R33 GTST and ive been told the brake pads and rotors are the same as the 300zx TT (just like the R32) and also wanted to know if the calipers are the same as well? im wanting to order all front Calipers, pads and rotors from nissan, ill be saying its for a 94 300zx, will i have any issues?
thanks

[Underoath.]

Hey guys, i found it a little hard to find what i needed going through all these pages so i copied and pasted everything into a single file, I figured i'd post it on here to help everyone else out as well.


Oil Filter - 240sx or 300zx
Fuel Filter - 300zx (have to remove the stock holder bracket in order to make it fit)
02 Sensor - 1990-94 300zx TT driver's side (left side)
Brake Pads - 300zx TT both front and rear.
Rotors - 300zx z32 tt front and rear.
Clutch - rb25 and VG30DE 300zx non turbo
Thermostat - VG30DE(TT)
Brake master cylinder - 91 Pathfinder
Rear shocks - S13(240sx) and GTR
Front tension rods - 300ZX(Z32) and S13
Almost all of the other suspension bars are the same as 300ZX including the energy suspension master bushing kit
Tie rod ends - maxima A32
Inner and outer (Front&Rear)CV boots - Z32 non-turbo
Trany front cover oil seal - D22 '00 K24DE
Shifter bushings - S13
Diff side oil seal - '90-'93 300zx Z32 non-turbo
Diff side bearing - Pathfinder WD21 '90-'93
Drive pinion oil seal - Pathfinder WD21 '88-'90
Drive pinion bearing - (F&R) Z32 non turbo
Inner rear CV joint - Z32
Front wheel bearing - Z32
Temp/Oil/Boost sensor - '90 Z32
Mag. starter solenoid switch - B14 91 GA16DE MT only
Power folding mirrors - S13
Heater core - U12
Blower fan and motor - P10
Rear inner Tie Rods - z32 300ZX TT
Lug Nuts - 300zx z32
Front inner tie rods - 90-96 infinity g20
Oil Sending Unit (pressure switch) - '91 300zx tt
Front Outer Tie Rods - 1995 Nissan Maxima
Alternator - 1989 - 1990 Nissan 240sx alternator off a KA24E or A32 Maxima
lower control arm - infinity q45
Ignitor - z32 http://forums.nicoclub.com/zerothread/251366

lowercontrol arm for the front or rear?

[wongger]

Knock sensor?

[Gregonater]

I was getting an alignment done today and they said I need new right and left upper pivot bearings and left upper outer bushings so that it will hold alignment. Does anyone know if these are shared with the z32? If not any other cars?

[nic-skyline]

is it the n/a 300zx fuel fuel filter compatible with the rb20det?? or?

[Supraclean]

I thimk so Nick I bought the same one and installed it. If you take it out of the box you should notice the top metal nipple should got an an almost 90 degree angle for the fuel line/fit in the bracket.

[johnnyjohnny]

For those with R33 GTS25T's, front shocks from a z32 300zx and rear shocks from s14 24sx fit our cars. I checked Nissan part #s in FAST, and also physically compared a set of z32 front shocks to mine. This is great news for those who, like me, want aftermarket shocks that are not height-adjustable coilovers. So, some options are:

Koni Sport (my personal favourite)
front - 8041-1118SPORT
rear - 8040-1226SPORT

KYB AGX
front - 741026/7
rear - 741045

Please note, this has only been confirmed for an R33 GTS25T. I have no idea if they fit R33 GTR or any R32.

[PrNsOwn04]

Hey guys just wanted to confirm front lower ball joints, front outer tie rods, and rear outer tie rods can all be used out of a 90-96 300zx?

[amnash]

how about the fuel injector seals to be used on rb20det using rb26 injectors????

[PrNsOwn04]

Oh forgot it's for a 92 gts4

[Hasley902]

how well does the 300 zx clutch hold up in a rb20 ?

[jboudreau]

how well does the 300 zx clutch hold up in a rb20 ?

i ran a 300zx clutch in my rb20 and it worked just fine.. just make sure your flywheel surface is good ( but i recommend getting it resurfaced anyways) the throw out bearing even works with it.. the only difference is the 300zx flywheel does not bolt to the rb20 block

[gtstevan]

can anyone tell me if the water pump and water pump gasket is compatible from any other vehicles?